DIY Tub Installation.
DIY Tub Installation.
Blog Article
The article in the next paragraphs relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is pretty much captivating. Check it out for your own benefit and see what you think of it.
Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough project. If the old tub is easily obtainable, the project can move rapidly; if you need to open a wall to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and set in the new one. Ensure you have certified on your own for the work and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may need an expert plumber to make tube links.
This write-up will help you install a new bathtub in your washroom if you have actually currently acquired a new tub as well as don't require to change the setup of your previous water supply pipes.
Your devices and also product list need to consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin ensuring that the washing machines remain in location in between the tap as well as the sink. Safeguard the tap in position with the supplier provided backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The previous kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if needed. Load the bath tub and also inspect the overflow electrical outlet and also the regular outlet for leaks.
Lastly, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub must wait up until the bath tub has actually been made use of at least once as this will settle it into its final position.
Preparing for the Setup
First of all, the sustaining framework provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing complications with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealer can crack relatively early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the market. It is a good idea to fit the floor tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I'm certainly very fascinated by A Step-by-Step Guide to Installing a Bathtub and I am assuming you enjoyed reading the entire piece. For those who liked our blog entry plz be sure to share it. Thank you for your time. Don't hesitate to check our site back soon.
Estimating Report this page